throttle will it work

[shergar]

i was thinking of using this throttle pull on a rd500 build im doing using pwk28 carbs do you think it will work lads ? http://www.ebay.co.uk/itm/231818853803? ... EBIDX%3AIT" onclick="window.open(this.href);return false; or do i need to use the tz style twin pull /pull ? thanks

[Ade SYM]

Hi

Its says it is a push / pull throttle so does exactly that.

If you are using mikuni 28mm carbs you need either a single or double cabled pull throttle which are readily available through the same manufacturer.

If you get a single you will need a 4 into 1 splitter and a double x 2, 2 into 1 splitters

Hope this helps

Thanks Ade

[shergar]

iv seen guys using that this type throttle on lc 350 using just a single cable but not sure what carbs , i just like the look of this one . yes im using 28 carbs ade . p

[silverstrom]

iv seen guys using that this type throttle on lc 350 using just a single cable but not sure what carbs , i just like the look of this one . yes im using 28 carbs ade . p

Because the 350 (outside of the USA) uses only 1 throttle cable to run 2 carbs. There is no push cable. Look around the forum and you'll see similar throttles to the one you show and they use a splitter to run all 4 carbs. One is here http://www.rzrd500.com/500phpBB3/viewto ... =7&t=12549" onclick="window.open(this.href);return false;

Bill Wilson makes something similar, but he took a different approach. His is round http://www.rzrd500.com/500phpBB3/viewto ... &start=165" onclick="window.open(this.href);return false;

[Stinke]

Hi, if you are using keihin 28 pwk just buy a throttle cable for a Suzuki rg500 then you can use your standard puller with just a little modifikation. And if you are going tu use the oil pump you just take the oil cable bit from rz/rd cable and put in the rg500-splitter (I think I did a small adjustment on the splitter, just drilling a bigger hole for the rz oil cable). This is a cheap and easy fix, no need for fancy billet stuff

http://www.wemoto.com/bikes/suzuki/rg_5 ... nky_glide/" onclick="window.open(this.href);return false;

[WVWRZ500N]

i was thinking of using this throttle pull on a rd500 build im doing using pwk28 carbs do you think it will work lads ? http://www.ebay.co.uk/itm/231818853803? ... EBIDX%3AIT" onclick="window.open(this.href);return false; or do i need to use the tz style twin pull /pull ? thanks

Email me directly. I've set up my Throttle Cable Kit to work with PWK28s already. I also sell all the brackets you'll need to relocate the choke and petcock.

[Ron57]

Hi, I've just set up 28mm carbs on my RZ500 used Bill Wilson's billet throttle cables used the oil pump cable and throttle cable off the RZ, made a new inner cable up so I could keep the original throttle.
Cheers Ron.

[shergar]

Hi, I've just set up 28mm carbs on my RZ500 used Bill Wilson's billet throttle cables used the oil pump cable and throttle cable off the RZ, made a new inner cable up so I could keep the original throttle.
Cheers Ron.

is the original throttle not a push / pull system as i thought it was ? ta

[shergar]

Hi

Its says it is a push / pull throttle so does exactly that.

If you are using mikuni 28mm carbs you need either a single or double cabled pull throttle which are readily available through the same manufacturer.

If you get a single you will need a 4 into 1 splitter and a double x 2, 2 into 1 splitters

Hope this helps

Thanks Ade

so do you think bill wilsons set up is the way to go if i go with a single pull ade ? paul

[Ade SYM]

Hi

Its says it is a push / pull throttle so does exactly that.

If you are using mikuni 28mm carbs you need either a single or double cabled pull throttle which are readily available through the same manufacturer.

If you get a single you will need a 4 into 1 splitter and a double x 2, 2 into 1 splitters

Hope this helps

Thanks Ade

so do you think bill wilsons set up is the way to go if i go with a single pull ade ? paul

Hi

I actually used the 4 into 1 splitter on my bike and with a similar throttle you have shown and it worked fine

It was a little hard on the wrist after a while but nothing excessive

Ade

[hybrid]

I used two banshee splitters along with my original RZ500 splitter.
Just had to modify the banshee ones for length and to connect to the original splitter.