I'm performing a total restoration of my 1984 RD500LC. After completely stripping the bike to get the frame shot blasted and powder coated, I found these 4 metal rings on the garage floor. They measure about 20mm across and have a thickness of a couple of mm. Does anyone know where they go?
Thanks
Steve.
Sent from my HTC Desire 530 using Tapatalk
Mystery Rings
Moderator: rztom
Mystery Rings
Current Bikes
1984 47X RD500LC, 2018 Triumph Speed Triple RS, 1999 Honda CB600F Hornet
Past Bikes Include
RD250LC, RD350YPVS LC2 Race Bike, RD350F2, 1976 CB400F
1984 47X RD500LC, 2018 Triumph Speed Triple RS, 1999 Honda CB600F Hornet
Past Bikes Include
RD250LC, RD350YPVS LC2 Race Bike, RD350F2, 1976 CB400F
- Rick Lance
- Posts: 366
- Joined: Thu Nov 17, 2005 11:12 am
- Location: Leicester, NC
- Contact:
Re: Mystery Rings
Back on the floor would be as good a place as any. They aren't part of a 500 Yamaha (unless they are a crude aftermarket attempt at imitating an exhaust gasket).
My apologies. I misread the scale. Glad to see you figured it out.
BTW, please make sure that your chain blocks inside the swingarm are a proper fit for the 17 mm axle you are using. The slots in the swingarm where your spacer rings fit should not be carrying any load.
My apologies. I misread the scale. Glad to see you figured it out.
BTW, please make sure that your chain blocks inside the swingarm are a proper fit for the 17 mm axle you are using. The slots in the swingarm where your spacer rings fit should not be carrying any load.
Last edited by Rick Lance on Wed Jan 10, 2018 10:59 am, edited 2 times in total.
If I disagree with everyone, that doesn't make me right. If I take the side of only one, it doesn't end the fight. If my position's strong enough from exposure to the light, you may see things my way when we share the same highway.
Re: Mystery Rings
Well I found a home for them. Not standard I'm sure. I thought they might be spacers between the sub-frame and frame but they seem to fit in the swinging arm Axel slots. Maybe I have an RZV swinging arm?
Sent from my HTC Desire 530 using Tapatalk
Sent from my HTC Desire 530 using Tapatalk
Current Bikes
1984 47X RD500LC, 2018 Triumph Speed Triple RS, 1999 Honda CB600F Hornet
Past Bikes Include
RD250LC, RD350YPVS LC2 Race Bike, RD350F2, 1976 CB400F
1984 47X RD500LC, 2018 Triumph Speed Triple RS, 1999 Honda CB600F Hornet
Past Bikes Include
RD250LC, RD350YPVS LC2 Race Bike, RD350F2, 1976 CB400F
Re: Mystery Rings
Seems you have a swingarm for a larger diameter rear axle and someone has machined these spacers to fit your smaller axle into it.
Re: Mystery Rings
RZV swing arm is the same as RD/RZ swing arm.Linx wrote:Well I found a home for them. Not standard I'm sure. I thought they might be spacers between the sub-frame and frame but they seem to fit in the swinging arm Axel slots. Maybe I have an RZV swinging arm?
Re: Mystery Rings
God knows what has gone on there then. Everything else fits OK. Are they both alloy?
Sent from my HTC Desire 530 using Tapatalk
Sent from my HTC Desire 530 using Tapatalk
Current Bikes
1984 47X RD500LC, 2018 Triumph Speed Triple RS, 1999 Honda CB600F Hornet
Past Bikes Include
RD250LC, RD350YPVS LC2 Race Bike, RD350F2, 1976 CB400F
1984 47X RD500LC, 2018 Triumph Speed Triple RS, 1999 Honda CB600F Hornet
Past Bikes Include
RD250LC, RD350YPVS LC2 Race Bike, RD350F2, 1976 CB400F